Home UPS 850 VA Installation and Operation (BI850SINE) Overview The APC by Schneider Electric Home UPS provides power to connected equipment during a power outage. If there is a loss of power or if the mains voltages are abnormal, the UPS will automatically switch any connected equipment to battery power. The UPS can be hardwired into a home electrical system to supply power to equipment such as lights, fans, televisions, and personal computers.
Safety Caution: The Home UPS should be installed by an APC Service Provider or a licensed electrician. Failure to do so may damage the Home UPS and void the warranty. Caution: The Home UPS must be connected to an appropriate battery. Use APC branded batteries because the charging output characteristics of the Home UPS are specifically designed to match APC branded batteries, ensuring the quickest recharge times and longest overall lives. Note: It is not recommended to connect more than one battery in parallel to the Home UPS as it may not be able to completely recharge the multiple batteries between power outages, leaving the batteries in a chronic state of low voltage. Do not operate this unit in direct sunlight, in excessive heat, in with fluids, or where there is excessive dust or humidity.
APC Information Toll free (BSNL Network): 1-800-4254-272 All other networks: (add city code) 39022272
[email protected] www.apc.com/in
Product Overview
bu132a
Front
INVERTER LOAD The INVERTER LOAD LEDs will illuminate when the Home UPS switches to battery LED S power and indicate the percentage of the unit output capacity being used by the connected equipment. • 50%: the unit is using 33-66% of output capacity • 75%: the unit is using 66-85% of output capacity • 100%: the unit is using 85-100% of output capacity
FAULT START/MUTE/ TEST
Note: When the Home UPS is receiving Mains power, these will not be illuminated. If illuminated, the unit is overloaded, has a shorted output, has overheated, or there is an internal electrical fault. APC Technical . Start: Press once to apply power to the unit. If the unit is in AWAY mode, and there is no mains input power, press and hold START for two seconds to connect the load to backup power. This will put the unit into HOME mode. Mute: Press and hold for one second to mute any audible alarms. Test: Press and hold for two seconds to start a diagnostic self test.
Note: This button will illuminate when the Home UPS is disabled (in AWAY mode). If illuminated, the unit is receiving mains power. If illuminated, the unit is supplying battery power to the connected equipment. C HARGING If blinking, the unit is receiving input mains power and is recharging the battery. If illuminated and solid, the battery is fully charged and the unit is receiving input mains power. CHECK BATTERY If blinking, the unit is not able to charge the battery. The battery may have a shorted cell, low water level, or be near the end of its life. Replace the battery. H OME /A WAY Home: Set the switch to HOME so that the unit will switch to battery power in the event of a power outage. Away: Set the switch to AWAY so that the unit will not switch to battery power during a power outage. This allows the battery to recharge, but prevents unnecessary discharges and extends the life of the battery. If the LED above this switch is illuminated red, the unit is in AWAY mode.
ON MAINS ON BATTERY
2
APC Home UPS 850 VA SINE
bu138a
Rear
UPS/INVERTER switch
UPS: Use with personal computer and small electronic devices that require a
regulated input range of 190-260 Vac. The Home UPS will ensure that connected equipment is only exposed to safe voltages by switching to battery power more often. This will decrease battery run time.
12 V battery cables
AC Output AC Input Circuit breaker
Battery fuse CHARGER OUTPUT switch
INVERTER: Use with household lights, fans, and other home electronic appliances that can tolerate less regulated input voltage ranges of 100-290 Vac. In this mode, the unit will switch to battery power less often. Connect a flat-plate or tubular 12 V battery. Ensure that the CHARGER O UTPUT switch is set to the position that matches the size of the battery. Note: A Sealed Maintenance Free (SMF) battery can be connected to the Home UPS to provide backup power. The SMF battery may have a shorter lifespan when used with the Home UPS because it has a different charging profile than a flat-plate or tubular battery. Connect electrical devices such as desktop computers, televisions, fans, or lights. Connect the unit to mains power. The circuit breaker will trip if there is an overload while the unit is operating on mains power. Press to reset the circuit breaker. Note: If the unit is overloaded, the circuit breaker will trip. There is no indication of this on the front of the unit. If the battery terminals are reversed during installation, the fuses will protect the unit from damage. Set the switch to match the size of the battery that is connected to the unit. This will ensure that the battery receives the correct charging current to prevent overcharging and undercharging, which will extend the life of the battery. See Installation for more information. Only an APC authorized technician should adjust this setting. Note: To ensure the longest possible battery life, use APC branded batteries.
Installation Install the Home UPS on a flat surface. Note: If you are installing the Home UPS on the top of an APC Battery Cabinet (part number LUBC), remove the stabilizing foot at the front of the unit.
APC Home UPS 850 VA SINE
3
Connect External Battery Electrical Hazard: Do not make with both of the battery terminals simultaneously with metal parts like screw drivers or spanners. Sparking may occur during connection of battery cables to battery terminals. Use only the battery cables provided with the unit to connect the external battery. Do not extend the length of these cables. 1. Use a Phillips screwdriver to open the metal at the rear of the unit to access the CHARGER OUTPUT switch. 2. Select the appropriate setting for the battery that will be used with the Home UPS. Charger Output 8A
Battery Size (C20 Rating) Switch position 80-100 Ah
10 A
110-120 Ah
13 A
130-150 Ah
15 A
160-180 Ah
3. Connect the red cable to the Positive (+) battery terminal. 4. Connect the black cable to the Negative (-) battery terminal. 5. Close the metal access and reinstall the screw removed in step 1.
Connect equipment to the Home UPS Caution: Ensure that all equipment that will be connected to the UPS during set up is disconnected from power and turned OFF.
1. Set the Home/Away switch on the front of the unit to HOME. 2. Connect equipment to the Home UPS. Use the 15 A three-pin connector on the rear of the unit.
Typical Home/Office Wiring after Home UPS Installation E
E
Electricity N Board L Meter
N
Double-Pole Switch Lighting Circuit
Input Output Wiring for Home UPS
4
Load bu145a
L
APC Home UPS 850 VA SINE
Connect the Home UPS to mains power 1. Disconnect mains power to the wall outlet to which the Home UPS will be connected. 2. Connect a 15 A three-pin plug (not included) to the input cable on the rear of the unit. a. Red wire - Phase/Line b. Black wire - Neutral c. Green/Yellow wire - Earth/Ground 3. Connect the Home UPS to the wall outlet using the power cord on the rear of the unit. 4. Turn ON the connected equipment. 5. Reconnect mains power to the wall outlet. 6. Ensure that the ON MAINS and CHARGING LEDs on the front of the unit are illuminated.
Test the Home UPS Test that the Home UPS is connected properly and will the connected equipment in the event of a power outage. 1. Ensure that the Home UPS is On and that the equipment connected to the UPS is On. 2. Disconnect mains power to the wall outlet to which the UPS is connected. 3. that the connected equipment is still On. 4. On the front of the Home UPS, the ON BATTERY and INVERTER LOAD LEDs should be illuminated. This will indicate that the UPS has switched the power supply to the equipment from mains power to battery power. Note: If the connected equipment turned Off when the mains power to the UPS was disconnected, the UPS did not transfer the equipment to battery power. Ensure that the UPS and the connected equipment are properly connected. See “Troubleshooting” for more information, if the problem is not solved by troubleshooting, APC Customer . Caution: If all of the INVERTER LOAD LEDs and the FAULT LED on the front of the Home UPS are illuminated, the unit is overloaded. Disconnect some of the equipment that is connected to the UPS. The unit will automatically restart after 60 seconds.
Operation Auto restart. If all of the INVERTER LOAD LEDs and the FAULT LED on the front of the Home UPS are illuminated, the unit is overloaded. The Home UPS will continue to supply power for 60 seconds before it trips and then will automatically restart.
If the load drawn from the connected equipment is not reduced, the Home UPS will restart itself three times, and then completely turn Off, disconnecting power to connected equipment. Disconnect some of the connected equipment to reduce the amount of power drawn from the Home UPS. Press START on the front of the unit to restart the Home UPS. Self test. The Home UPS will perform a self test every time the unit is turned on. If the unit is On mains power, press TEST on the front of the unit. Recharge the battery. The battery connected to the Home UPS will automatically recharge when the unit is operating on mains or generator power. Low voltage shutdown. The Home UPS will automatically shut down if the battery power drops below a safe voltage. This prevents the battery from being fully discharged.
APC Home UPS 850 VA SINE
5
Increase battery lifespan. Several factors can impact the lifespan of the battery. The ambient temperature, the number of discharge cycles, age, maintenance of voltage levels, recharging cycles, and the amount of discharge per cycle can all decrease the lifespan of the battery.
Follow these suggestions to increase the life of the battery: • Set the HOME/AWAY switch to AWAY when leaving the house for extended periods of time. This will prevent unnecessary discharges of the battery during power outages. • Connect only essential equipment to the Home UPS to minimize the amount of discharge of the battery and to reduce the recharge time. • Store the battery in a cool place, away from heat sources like direct sunlight or air conditioning exhaust. Avoid keeping it in areas above 30 C. • Batteries should be recharged immediately after each discharge and should never be allowed to stay in a discharged state. • Maintain proper water levels in the battery using only distilled water. See the information provided with the battery for additional information on water levels. • Ensure that the CHARGER OUTPUT switch on the rear of the unit is set to the correct Ah rating. See “Rear ” on page 3 for more information. • Batteries that are stored for long periods or time will eventually lose their charge, especially in higher ambient temperatures. Always maintain a fully charged battery, even when it is not in use.
Troubleshooting Problem
Possible Cause
The Home UPS does not supply The unit is overloaded and the circuit power the load while connected to breaker has tripped. mains power
Corrective Action Disconnect or turn Off some of the equipment that is connected to the UPS. Reset the circuit breaker on the rear of the unit. APC Customer Service.
The unit has an internal electrical fault. (The FAULT LED on the front of the unit will be illuminated.) The Home UPS does not supply The unit is overloaded. Disconnect or turn Off some of the power to the connected equipment equipment that is connected to the UPS. during a power outage. Press the START button. The battery fuse has opened, possibly Replace the three fuses on the rear from an improper installation in which the of the unit and ensure that the polarities polarity of the battery was reversed. of the battery are not reversed. If fuse opens again, APC Customer Service. The battery or wiring connections are Clean the battery terminals and secure cables loose or corroded. to battery terminal. Check for any loose connections on the 15 A input plug.
Allow battery to fully recharge. Set the HOME /AWAY switch to AWAY to prevent discharge). The battery may take 10-12 hours to complete recharge. Set the switch to HOME. If the unit is not receiving mains power, press START. The Home UPS is beeping This can be caused by low battery voltage, Recharge battery. If this does not solve continuously. failed or dead battery, an output short the problem, APC Customer circuit, over temperature. Service. Television experiences interference The Home UPS may be causing Move the television at least one meter interference. away from the Home UPS. The battery has discharged or is dead. (The Home UPS automatically shuts off when battery voltage drops below a safe voltage). The HOME/AWAY switch is set to AWAY.
6
APC Home UPS 850 VA SINE
Specifications Input Voltage, nominal
230 Vac
Operation voltage as Inverter
100-290 Vac
Operation voltage as UPS
190-260 Vac
Input frequency
45-53 Hz
Maximum input current
10 A
Maximum input voltage without damage
300 Vac
Output Wave form
Sine wave
Power rating on Mains
850 VA at 230 Vac
Output voltage on Mains (UPS)
190-260 Vac (Mains voltage ed to load)
Output voltage on Mains (Inverter)
100-290 Vac (Mains voltage ed to load)
Output frequency on Mains
45-53 Hz (voltage ed to load)
Output frequency on Battery
50 Hz +/- 1 Hz
Battery Charger Type
Microprocessor controlled, 3-stage regulated charging
Output
Selectable output current: 8 A, 10 A, 13 A, 15 A
Recharge time
10-12 hours
Safety Protection Overload on Mains
Thermal circuit breaker, with reset button
Overload on Battery
Shutdown after three automatic reset attempts
Reverse battery polarity
Fuses on rear
Low battery voltage
Automatic shutdown
Other protection circuitry
Short circuit protection, Over temperature protection
Environmental Operating temperature
0-45°C
Storage temperature
0-60°C
Humidity
0-95% non-condensing
Altitude
0-3000 m
Physical Dimensions W x D x H
35.0 x 26.5 x 14 cm
Net weight
11 kg
Input connection to Mains
1.5 m hardwired power cord with stripped leads
Input connection to Battery
0.8 m hardwired cable with crimped terminal lugs
Output connection
15 A (India)
APC Home UPS 850 VA SINE
7
Limited Warranty Warranty on this Home UPS covers defects in materials and workmanship for a period of 24 months from the date of installation or from the date of purchase by the customer; OR 26 months from the date of manufacture, whichever is earlier. All warranty claims must be brought to APC’s attention prior to the expiration of the warranty. To obtain service under this warranty you must obtain a Return Material Authorization (RMA) number from APC Customer Service. It is APC’s sole discretion to fulfill this warranty by either: 1. Repairing the Home UPS with components that are new, used, remanufactured, or equivalent to the original components at no charge, or 2. Exchanging the Home UPS with a factory reconditioned equivalent unit at no charge. All units serviced within the warranty period are warranted for either 90 days or the remainder of original warranty period, whichever is longer. If a Home UPS fails upon initial installation, APC Customer Service must be notified within two (2) weeks from the date of invoice. Warranty Exclusions: The following are not covered under this warranty: – Normal reductions in backup time due to battery aging or lack of battery maintenance. See “Increase battery lifespan” on page 6. – Incidental damage to any other equipment used in conjunction with the Home UPS. This warranty will be considered void if: – The Home UPS is not ed within 15 days of product installation. Please refer to the “Product Registration” card enclosed. – The serial number sticker on the Home UPS is tampered with or defaced. – The Home UPS is used in a manner inconsistent with the published operating instructions specified in this manual (including, but not limited to: improper site preparation, misapplication or mishandling.) – Batteries are connected which require higher charging current than the Home UPS can provide. See “Connect External Battery” on page 4 for compatibility information. – The unit is damaged due to abuse; accidents; negligence; improper installation; faulty building wiring; or entry of insects, rodents, animals, reptiles, sand, liquids, etc. – Parts are used that are not supplied or recommended by APC. – Repair, maintenance, or modification is performed by an unauthorized repair facility. If an APC battery is being used with the Home UPS, the warranty for this APC battery is 18 months from the date of purchase by the customer. The warranty of any APC battery will be void in the event that periodic maintenance is not carried out. If the battery used with the APC Home UPS is not an APC branded battery, then the must obtain any battery warranty service from the battery manufacturer, and not APC.
Customer and warranty information is available at the APC Web site, www.apc.com. © 2010 APC by Schneider Electric. APC and the APC logo are owned by Schneider Electric Industries S.A.S., American Power Conversion Corporation, or their d companies. All other trademarks are property of their respective owners.
990-3860A 03/2010