Four Quadrant Operation 4r4v36

FOUR QUADRANT DC MOTOR SPEED CONTROL WITHOUT MICROCONTROLLER Submitted by:

CONTENTS Introduction Block diagram Four quadrant operation of DC motor 555 timer L293D IC DC Motor Schematic & Working of the project Advantages Applications Future scope Conclusion

Project overview

The aim of the project is to develop a speed

control system for DC motor using fourquadrant chopper. Using four-quadrant chopper it is possible to demonstrate forward &reverse motoring and braking. The speed of DC motor is directly proportional to armature voltage and inversely proportional to flux.  By maintaining the flux constant, the speed can be varied by varying the armature voltage. The direction of rotation is reversed by reversing armature voltage.

Contd..

In this project, we use a small FHP (Fractional

Horse Power) DC motor whose field comprises of a permanent magnet. The armature of that is excited by a variable dc supply obtained from four-quadrant chopper. The system is provided with various control keys, such as START, STOP, FORWARD, REVERSE, FORWARD BRAKE, and REVERSE BRAKE. Using these keys, the can set the motor to run in any one of the following modes, namely Forward motoring, Reverse motoring, Forward braking and reverse braking. The speed can be varied by varying the voltage given to the PWM converter (using potentiometer).

Block diagram

FOUR QUADRANT OPERATION OF DC MOTOR DC. Motor Equation

Va = E a + R aI a

E a = kF wm Tem = kF I a

(

I aR a wm = Va kF

)

THE FUNCTION 4 QUADRANT DC MOTOR

555 TIMER The 555 Timer IC is an integrated circuit (chip) implementing

a variety of timer and multivibrator applications. The original name was the SE555 (metal can)/NE555 (plastic

DIP) and the part was described as "The IC Time Machine". Depending on the manufacturer, the standard 555 package

includes over 20 transistors, 2 diodes and 15 resistorson a silicon chip installed in an 8-pin mini dual-in-line package (DIP-8)

PIN DIAGRAM OF 555

The 555 timer IC is a simple 8 pin DIL package IC. It can: be used as a monostable be used as an astable source or sink 100mA use supply voltages of 5v to 15v disrupt the power supply - use a decoupling capacitor!

MOTOR driver L293D  L293D is a dual H-bridge

motor driver integrated circuit (IC).  Motor drivers act as current amplifiers since they take a low-current control signal and provide a higher-current signal.  This higher current signal is used to drive the motors.  L293D contains two inbuilt H-bridge driver circuits. In its common mode of operation, two DC motors can be driven simultaneously, both in forward and reverse direction.

Operation of motor driver  L293D has 2 set of arrangements where one set has input 1, input 2, output 1 and output 2 and other set has input 3, input 4, output 3 and output 4, according to block diagram if pin no 2 & 7 are high then pin no 3 & 6 are also high. If enable 1 and pin number 2 are high leaving pin number 7 as low then the motor rotates in forward direction. If enable 2 and pin number 10 are high leaving pin number 15 as low then the motor rotates in forward direction.

Contd.. If enable 1 and pin number 2 are low

leaving pin number 7 as high then the motor rotates in reverse direction. If enable 2 and pin number 15 are high leaving pin number 10 as low then the motor rotates in forward direction.

DC- MOTOR A DC motor is an electric motor that runs on direct current (DC) electricity. In any electric motor,

operation

is

based

on

simple

electromagnetism. A simple 2-pole DC electric motor (here red represents a magnet or winding with a "North" polarization, while green represents a magnet or winding with a "South" polarization). Every DC motor has six basic parts -- axle, rotor (a.k.a.,

armature),

stator,

magnet(s), and brushes.

commutator,

field