Acmosil 36-4142 E 4k3356

Safety Data Sheet ACMOS CHEMIE KG

according to Regulation (EC) No 1907/2006

ACMOSIL 36-4142 Issue date : 15.02.2013

Page 1 of 14

SECTION 1: Identification of the substance/mixture and of the company/undertaking 1.1. Product identifier

ACMOSIL 36-4142 1.2. Relevant identified uses of the substance or mixture and uses advised against Relevant identified uses

Release agent for PUR Uses advised against

The product is for industrial and professional use only - no consumer product. 1.3. Details of the supplier of the safety data sheet Manufacturer

Company name: Street: Place: Post-office box: Telephone: e-mail:

ACMOS CHEMIE KG Industriestrasse 49 D-28199 Bremen 10 10 69 D-28010 Bremen +49 (0)421-5189-0 [email protected]

person: Internet: Responsible Department:

Mr. Dryhaus www.acmos.com Laboratory (Division : Occupational- / Product security) - See under section 16

Telefax: +49 (0)421-511415

Supplier

Company name: Street: Place:

ACMOS CHEMIE KG Industriestrasse 49 D-28199 Bremen

Post-office box:

10 10 69 D-28010 Bremen

Telephone:

+49 (0)421-5189-0

e-mail: person:

[email protected] Mr. Dryhaus

Internet: Responsible Department:

www.acmos.com Laboratory (Division : Occupational- / Product security) - See under section 16

1.4. Emergency telephone number:

Telefax: +49 (0)421-511415

+49 (0)551-19240 (Emergency information service / official advisory body: Giftinformationszentrum Nord, Universität Göttingen, 24 h service)

SECTION 2: Hazards identification 2.1. Classification of the substance or mixture Classification according to Directive 67/548/EEC or Directive 1999/45/EC

R phrases: May cause long-term adverse effects in the aquatic environment. Repeated exposure may cause skin dryness or cracking. This mixture is classified as hazardous according to the new EC-preparation directive 1999/45/EC. 2.2. Label elements R phrases 53 Revision No: 1,14

May cause long-term adverse effects in the aquatic environment. GB - EN

Revision date: 13.02.2012

Safety Data Sheet according to Regulation (EC) No 1907/2006

ACMOS CHEMIE KG

ACMOSIL 36-4142 Issue date : 15.02.2013

Page 2 of 14

66

Repeated exposure may cause skin dryness or cracking.

S phrases 23 24 61

Do not breathe spray . Avoid with skin. Avoid release to the environment. Refer to special instructions / Safety data sheets.

Additional advice on labelling The product is classified and labelled in accordance with the CHIPS Regulations 1994. Preparation Directive 1999/45/EC. 2.3. Other hazards

Adverse physicochemical effect(s) : See section 9 for physical and chemical properties. Adverse human health effect(s) and symptom(s) : See section 11 for toxicological information. Adverse environmental effect(s) : See section 12 for environmental information. Other adverse Hazard(s) : No special remarkable hazards. Results of PBT-/vPvB-assesment : See under section 12.

SECTION 3: Composition/information on ingredients 3.2. Mixtures Chemical characterization Mixture of active ingredients Hazardous components EC No CAS No Index No REACH No 918-167-1 90622-57-4

Quantity

Chemical name Classification GHS classification

75 - 80 %

hydrocarbons, C11-C12, isoalkanes, <2% aromatics Xn - Harmful R53-65-66 Asp. Tox. 1, Aquatic Chronic 4; H304 H413

01-2119472146-39

Further Information Subdivision of relevant R-, H-, EUH-Phrases in full text (number and wording) see under section 16.

The above mentioned EC-No. (Provisional List Number 9xx-xxx-x) is a specific subset of the specified CAS-No. and was associated with the registration process automatically (without CAS-No. or numeric identifier). An official announcement by the EC inventory will follow after evaluation of substance identity by the ECHA. The new nomenclature of hydrocarbon solvents is only related with group names of the HSPA (Hydrocarbon Solvents Producers Association). The previously used CAS-No. continues serving as a reference for different global inventories .

SECTION 4: First aid measures 4.1. Description of first aid measures General information Take off all contaminated clothing immediately. Wash contaminated clothing before re-use. If victim has stopped breathing: Artificial respiration and/or oxygen may be necessary. If victim is unconscious but breathing: Victim to lie down in the recovery position, cover and keep him warm. If victim is conscious: Move out of dangerous area. If a person vomits when lying on his back, place him in the recovery position. Consult a physician if necessary Show this safety data sheet to the doctor in attendance. Revision No: 1,14

GB - EN

Revision date: 13.02.2012

Safety Data Sheet ACMOS CHEMIE KG

according to Regulation (EC) No 1907/2006

ACMOSIL 36-4142 Issue date : 15.02.2013

Page 3 of 14

Protection of first-aiders : wear personal protective equipment See under section 8. Notes to physician : Aspiration may cause pulmonary oedema and pneumonitis. Symptoms may be delayed. After inhalation Move to fresh air in case of accidental inhalation of vapours. In case of shortness of breath, give oxygen. Symptoms of overexposure are dizziness, headache, tiredness, nausea, unconsciousness, cessation of breathing. If symptoms persist, call a physician. After with skin Wash off with soap and water. Preventive skin protection. After with eyes Rinse thoroughly with plenty of water for at least 15 minutes and consult a physician. If eye irritation persists, consult a specialist. After ingestion Do not induce vomiting. Consult a physician. Risk of product entering the lungs on vomiting after ingestion. Never give anything by mouth to an unconscious person. 4.2. Most important symptoms and effects, both acute and delayed See under section 11. 4.3. Indication of any immediate medical attention and special treatment needed Treat symptomatically.

In case of ingestion, the stomach should be emptied by gastric lavage under qualified medical supervision. Later control for pneumonia and lung oedema.

SECTION 5: Firefighting measures 5.1. Extinguishing media Suitable extinguishing media Use extinguishing measures that are appropriate to local circumstances and the surrounding environment. water spray, sand, foam, dry chemical, carbon dioxide (CO2) Extinguishing media which must not be used for safety reasons Do not use a solid water stream as it may scatter and spread fire. 5.2. Special hazards arising from the substance or mixture Fire will produce dense black smoke containing hazardous combustion products. Under conditions giving incomplete combustion, hazardous gases produced may consist of : Carbon monoxide, carbon dioxide (CO2), hydrocarbons, smoke In principle, fire gasses of organic materials have to be classified as toxic to the respiratory system. 5.3. Advice for firefighters In the event of fire, wear self-contained breathing apparatus. In the event of fire and/or explosion do not breathe fumes. Move to fresh air in case of accidental inhalation of fumes from overheating or combustion. Additional information Usual measures of preventive and averting fire protection. In the event of fire, cool tanks with water spray. Fire residues and contaminated fire extinguishing water must be disposed of in accordance with local regulations. Collect contaminated fire extinguishing water separately. This must not be discharged into drains.

SECTION 6: Accidental release measures

Revision No: 1,14

GB - EN

Revision date: 13.02.2012

Safety Data Sheet ACMOS CHEMIE KG

according to Regulation (EC) No 1907/2006

ACMOSIL 36-4142 Issue date : 15.02.2013

Page 4 of 14

6.1. Personal precautions, protective equipment and emergency procedures Avoid with skin and eyes. Try to avoid breathing vapours or spray mist. If product is heated or sprayed : Remove all sources of ignition. Do not smoke. Keep people away from and upwind of spill/leak. Special danger of slipping by leaking/spilling product. Prevent further leakage or spillage if safe to do so. Ensure adequate ventilation.

For non-emergency personnel : Walk out of the danger zone and notify trained personnel . If necessary, wear personal protective equipment. Never enter into a personal risk. See under section 8. Keep the factory emergency plan and the information chain. For emergency responders : The personal protective equipment must be adapted to the situation. 6.2. Environmental precautions Do not flush into surface water or sanitary sewer system. 6.3. Methods and material for containment and cleaning up Clean-up methods - large spillage : Dam up. Shovel into suitable container for disposal. Local authorities should be advised if significant spillages cannot be contained. Clean-up methods - small spillage : Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Take up mechanically and collect in suitable container for disposal . 6.4. Reference to other sections Further information see under section 8, 13.

SECTION 7: Handling and storage 7.1. Precautions for safe handling Advice on safe handling Prevent the creation of flammable or explosive concentrations of vapour in air and avoid vapour concentration higher than the occupational exposure limits. The product should only be used in areas from which all naked lights and other sources of ignition have been excluded. Use only in well-ventilated areas. When using, do not eat, drink or smoke. Advice on protection against fire and explosion Measures according to German "Explosion rules" required : Prevention measures regarding formation of explosible atmosphere (restriction and supervision of concentration, inertisation, airtightness, ventilation, warning device, etc.). Prevention measures regarding ignition of explosible atmosphere (zone graduation, removing of ignition sources, explosion-proof electrical installation, earthing, etc.). Constructive measures for restriction of effects regarding explosions (resistance to pressure of explosions, discharge of pressure of explosions, suppression of explosions, etc.).

Take precautionary measures against static discharges . Preparation may charge electrostatically: always use earthing leads when transferring from one container to another. To avoid ignition of vapours by static electricity discharge , all metal parts of the equipment must be grounded. Do not use pressure to empty drums. Keep product and empty container away from heat and sources of ignition. Do not smoke. Vapours may form explosive mixture with air. Spray mist may be flammable at temperatures below the flash point. Vapours are heavier than air and may spread along floors . Electrical equipment should be protected to the appropriate standard. Fire-fighting equipment on the basis of class B. Further information on handling Reference on types of requiring special precautionary measures : Particularly at work places with filling and transfer procedures into other containers, as well as with weightening and mixture processes an effective exhaust ventilation has to be guaranteed . Revision No: 1,14

GB - EN

Revision date: 13.02.2012

Safety Data Sheet ACMOS CHEMIE KG

according to Regulation (EC) No 1907/2006

ACMOSIL 36-4142 Issue date : 15.02.2013

Page 5 of 14

For restriction of emission on volatile organic compounds (VOC) the solvent vapours should be supplied to an exhaust air purification facility (filter, gas washer, incineration). 7.2. Conditions for safe storage, including any incompatibilities Requirements for storage rooms and vessels Keep containers tightly closed in a cool, well-ventilated place. The valid water and zoning ordinances must be observed. Design solvent resistant and tight floor. Advice on storage compatibility Stable under recommended storage conditions. Incompatible with oxidising agents. Further information on storage conditions Indoor stockability in closed unopened original containers : 6 months. Store at room temperature in the original container. Keep at temperatures between +10 and +30 °C. Do not store outside. Avoid heating and direct sunlight. See also instuctions on the label. 7.3. Specific end use(s)

Possibilities for substitution and references to less hazardous products : This product was designed for a special application purpose and optimized appropriately. In case of questions regarding product and application, please our field service in line with customer service or our technical sales department. Specific regulations of branch industries : Hazardous substance information systems of professional associations.

SECTION 8: Exposure controls/personal protection 8.1. Control parameters Additional advice on limit values

Recommended monitoring and observation processes : None known.

Control banding for chemicals according to the ILO CHEMICAL CONTROL TOOLKIT (ICCT) : ICCT-Guidelines and - Control Guidance Sheets : http://www.ilo.org/legacy/english/protection/safework/ctrl_banding/toolkit/main_guide.pdf Consider appropriate model solutions according to good engineering practices on deg the working process, if available. 8.2. Exposure controls

Appropriate engineering controls Design of appropriate work processes and engineering controls and the use of adequate materials (physical cut- off of man and machine, model solutions as certified working methods, working appliance according to the state of the art, optimization of process / spray robots, working appliance for prevention of skin , models of working times).

Preliminary concentration measurements : Suitable detector tubes for measuring the current concentration in the air at the workplace : DRÄGER test tubes short-term tubes (Internet : http://www.gasmesstechnik.de) References for design of technical equipment : See under section 7. Revision No: 1,14

GB - EN

Revision date: 13.02.2012

Safety Data Sheet ACMOS CHEMIE KG

according to Regulation (EC) No 1907/2006

ACMOSIL 36-4142 Issue date : 15.02.2013

Page 6 of 14

Execution of collective protection measures at source and appropriate organisational measures (local exhaust ventilation, ventilation by technical means, general ventilation, measures on averting a danger at breakdowns / at emergencies / after accidents, first-aid-measures, manner related measures : operating instruction / instruction of employees, occupational medicine health precaution). Provide appropriate exhaust ventilation at machinery. Where reasonably practicable this should be achieved by the use of local exhaust ventilation and good general extraction. If these are not sufficient to maintain concentrations of particulates and solvent vapour below the OEL, suitable respiratory protection must be worn. Execution of individual and personnel protection measures (personal protective equipment - PPE). Individual protection measures, such as personal protective equipment When using, do not eat, drink or smoke. General industrial hygiene practice. Handle in accordance with good industrial hygiene and safety practice. Respiratory protection

Breath protection at insufficient ventilation or prolonged exposition . Breathing apparatus needed only when aerosol or mist is formed. Observe limited carrying time. The use of filter equipment requires a minimum oxygen content of 17 Vol-% in the surrounding atmosphere and that the maximum permitted gas concentration - normally 0,5 Vol-% - is not exceeded. Half mask or quarter mask with combination filter A1P1/A2P2 for gases, vapors and particles. Filtering half mask or quarter mask with combination filter FFA 1 P1/FFA2P2 for gases, vapors and particles. (EN 405) Gas filtrating Half-face mask FFA (EN 405) Model 4251 (FFA1P1 - 1000 ml/m3) / 4255 (FFA2P2SL - 5000 ml/m3) - 3M, Internet : http://www.3m.com Half-face mask or Quarter-face mask with gas filter (EN 140) Filter type 6051 (A1 - 1000 ml/m3) / 6055 (A2 - 5000 ml/m3) - 3M, Internet : http://www.3m.com Full-face mask with gas filter (EN 136) Gas filter type : A, Indication colour : brown Skin protection Hand protection : Use only chemical protective gloves with CE-status of category III in accordance to EN 374. Suitable materials at long term, direct (Recommended : Preventive index 6, accordingly > 480 min. permeation time in accordance to EN 374) : Fluorine rubber / FKM / Viton (VITOJECT® - Art. No. 890) - Layer thickness : 0,7 mm Nitrile rubber / NBR (CAMATRIL VELOURS® - Art. No. 730) - Layer thickness : 0,4 mm

Suitable materials at short term or splash (Recommended : Preventive index 3, accordingly > 60 min. permeation time in accordance to EN 374) : Disposable gloves of special nitrile rubber / NBR (DERMATRIL® P - Art. No. 743) - Layer thickness : 0,2 mm Manufacturer : Kächele-Cama Latex GmbH, Industriepark Röhn, Am Kreuzacker 9, D-36124 Eichenzell, c/ o Tony O'Donovan, 2 Wyndham Road, New Waltham, Grimsby, N. E. Lincs, GB-DN36 4WA Telephone : +44-(0)1472232883, Telefax : +44-(0)1472232883, Internet : http://www.kcl.de, E-Mail : [email protected] The statements are based on self-tests, literary reference and information of glove manufacturers or have been derived from similar substances by analogy. Source : CHEMIKALIEN-MANAGER - KCL software for hand protection. It has to be noticed, that daily time of use of chemical protective gloves may be quite shorter in practice because of many factors of influence (e.g. thermal and mechanical stress as well as special conditions on the floor) than the permeation time determined in accordance to EN 374. The respective permeation time doubles/halvens at about 1,5 times larger/lower layer thickness. Declared permeation times according to EN 374 are not carried out under practical conditions. Therefore a maximum wearing time up to 50 % of breakthrough time is recommended. They relate to the pure solvent as mean component. Decrease wearing protection gloves to an inevitable degree to avoid skin rash. Technical and organizational protective actions have to be preferred. Wear under gloves made of cotton as possible. Change preventive gloves once by hour or Revision No: 1,14

GB - EN

Revision date: 13.02.2012

Safety Data Sheet ACMOS CHEMIE KG

according to Regulation (EC) No 1907/2006

ACMOSIL 36-4142 Issue date : 15.02.2013

Page 7 of 14

use special skin-protective preparations for protective gloves carrier, e.g. physioderm® proGlove Before removing gloves clean them with soap and water. Dispose preventive gloves after defect or expiry of wearing time. Check protective gloves to proper condition before usage. Preventive skin protection. : Draw up skin protection programme. Before starting work, apply solvent-resistant skincare preparations, e.g. sansibal® / sansibon®, dualin® Wash hands before breaks and on finishing work, e.g. ecosan®, topscrub® soft / topscrub® extra / topscrub® nature After cleansing, apply greasy skincare products, e.g. physioderm® creme, cura soft® / cUrea soft® Manufacturer : Peter Greven Physioderm GmbH, Procter-&-Gamble-Str. 26, D-53881 Euskirchen Telephone : +49-(0)2251 77617-61, Telefax : +49-(0)2251 77617-44, Internet : http://www.physioderm.de, E-Mail : [email protected] Other : Skin protection : Light protective clothing (EN 340) : Protective clothing (Category III according to EN 374, Type 4) - Spray tight clothing with protection against liquid aerosols (EN 14605, EN 468), e.g. TYVEK Classic Plus - Type 4/5/6 (Internet : http://www.dpp-europe.com/?lang=en), safety shoes, antistatic boots (EN 344) Eye / face protection safety glasses with side-shields (EN 166) Thermal hazards No thermal hazards during use of this product. Environmental exposure controls

Should not be released into the environment. Discharge exhaust air only with suitable seperators to atmosphere. Further information see under section 6.

SECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical properties

Physical state: Colour: Odour:

liquid colourless characteristic Test method

Not applicable

pH-Value: Changes in the physical state Melting point:

< - 20 °C Literary reference

Boiling point:

> 170 °C Literary reference Not applicable

Sublimation point:

not determined

Softening point: Flash point:

> 60 °C EN ISO 2719

Explosive properties Vapour/air-mixtures are explosive at intense warming. The statements for steam pressure, ignition point and explosion levels apply to the solvent / solvent mixture.

Lower explosion limits: Revision No: 1,14

0,6 vol. % Literary reference GB - EN

Revision date: 13.02.2012

Safety Data Sheet ACMOS CHEMIE KG

according to Regulation (EC) No 1907/2006

ACMOSIL 36-4142 Issue date : 15.02.2013

Page 8 of 14

Upper explosion limits:

7,0 vol. % Literary reference > 200 °C Literary reference

Ignition temperature: Oxidizing properties Not applicable

Vapour pressure: (at 20 °C) Vapour pressure: (at 50 °C) Density (at 20 °C): Water solubility: (at 20 °C) Solubility in other solvents: Partition coefficient:

< 1 hPa Literary reference < 6 hPa Literary reference 0,8 g/cm³ DIN 51757 < 0,1 g/L Literary reference miscible with most organic solvents Not applicable (Preparation)

Viscosity / dynamic: Viscosity / kinematic: (at 23 °C) Flow time: (at 23 °C) Vapour density: (at 25 °C) Evaporation rate: (at 20 °C)

not determined > 7 mm²/s 3 EN ISO 2431 39 s 3 EN ISO 2431 ~5.4 (Air=1), M~168 g/mol Literary reference < 0.1 (n-BuAc=1) Literary reference

Solvent separation test:

Not applicable not determined

Solvent content: 9.2. Other information

Solid content:

not determined

Gas group (94/9/EC) : IIA (maximum experimental safe gap > 0,9 mm) Temperature class (94/9/EC) : T3 (T > 200 °C ... <= 300 °C) Conductivity : < 10E-08 S/m Odor threshold : no data available

SECTION 10: Stability and reactivity 10.1. Reactivity

No decomposition if stored and applied as directed. 10.2. Chemical stability Stable at normal conditions 10.3. Possibility of hazardous reactions Exothermic reaction : See under section 10.5. 10.4. Conditions to avoid Heat. Further information see under section 7. 10.5. Incompatible materials oxidising agents 10.6. Hazardous decomposition products No decomposition if stored and applied as directed. Under fire conditions: See under section 5.

Revision No: 1,14

GB - EN

Revision date: 13.02.2012

Safety Data Sheet ACMOS CHEMIE KG

according to Regulation (EC) No 1907/2006

ACMOSIL 36-4142 Issue date : 15.02.2013

Page 9 of 14

SECTION 11: Toxicological information 11.1. Information on toxicological effects Toxicocinetics, metabolism and distribution

No toxical dates available. Not proofed mixture. The product was classified according to the conventionally method (based on the calculation procedure of the new EC-preparation directive 1999/45/EC). Information on likely routes of exposure / Symptoms related to the physical, chemical and toxicological characteristics : After ingestion : Ingestion may cause gastrointestinal irritation, nausea, vomiting and diarrhoea. Risk of product entering the lungs on vomiting after ingestion. Aspiration may cause pulmonary oedema and pneumonitis. Based on available data, the classification criteria are not met. After inhalation : Inhalation of aerosols may cause irritation to mucous membranes. Inhalation of vapours in high concentration can cause narcotic effects and metabolic acidosis . Symptoms of overexposure are dizziness, headache, tiredness, nausea, unconsciousness, cessation of breathing. After skin : May cause skin irritation in susceptible persons. Repeated or prolonged with the preparation may cause removal of natural fat from the skin resulting in non-allergic dermatitis and absorption through the skin. Solvents may degrease the skin. After eye : with eyes may cause irritation. High concentration of vapours may cause irritation to eyes and respiratory system and produce narcotic effects . Delayed and immediate effects as well as chronic effects from short and long -term exposure : Not relevant / no data available Interactive effects : Not relevant / no data available Absence of specific data : No data is available on the product itself. Description of possible hazardous to health effects is based on experience and/or toxicological characteristics of several components. Based on manufacturer datas of the main components the acute toxixity, the skin irritation, the mucous membrane irritation and the mutagenic potential of the mixture were evaluated. However, some datas are not complete regarding particular main components. Nevertheless according to the experience of the manufacturer there are no other hazards expected then those which are already mentioned on the label. Mixture versus substance information : Not relevant / no data available Acute toxicity The following informations are derived from the properties of the individual components. LD50/oral/rat = > 2000 mg/kg LD50/dermal/rabbit = > 2000 mg/kg LC50/inhalation/4h/rat = > 20 mg/l

Revision No: 1,14

GB - EN

Revision date: 13.02.2012

Safety Data Sheet according to Regulation (EC) No 1907/2006

ACMOS CHEMIE KG

ACMOSIL 36-4142 Issue date : 15.02.2013 CAS No

Chemical name Exposure routes

90622-57-4

Page 10 of 14

Method

Dose

h

Species

hydrocarbons, C11-C12, isoalkanes, <2% aromatics Acute oral toxicity

LD50

> 5000 mg/kg

rat

Acute dermal toxicity

LD50

> 3160 mg/kg

rabbit

Acute inhalation toxicity

LC50

> 5,6 mg/l

rat

4

Irritation and corrosivity Based on available data, the classification criteria are not met. Sensitising effects After inhalation : Based on available data, the classification criteria are not met. After skin : Based on available data, the classification criteria are not met. Severe effects after repeated or prolonged exposure Subacute to chronical toxicity : Based on available data, the classification criteria are not met. Carcinogenic/mutagenic/toxic effects for reproduction Based on available data, the classification criteria are not met. Other information no data available

SECTION 12: Ecological information 12.1. Toxicity No ecotoxical dates available. Not proofed mixture. The product was classified according to the conventionally method (based on the calculation procedure of the new EC-preparation directive 1999/45/EC).

Aquatic toxicity (Fish toxicity, Algae toxicity, Daphnia toxicity) : The following informations are derived from the properties of the individual components. LC50/96h/guppy = > 100 mg/l EC50/72h/algae = > 100 mg/l EC50/48h/daphnia = > 100 mg/l Terrestric toxicity (Bird toxicity, Beneficial insect, Rainworm toxicity) : no data available Plant toxicity : no data available Behaviour in waste water treatment plants : no data available CAS No

Chemical name Aquatic toxicity

90622-57-4

Method

Dose

Species

h

hydrocarbons, C11-C12, isoalkanes, <2% aromatics Acute fish toxicity

LC50

> 1000 mg/l

Oncorhynchus mykiss

96

Acute algae toxicity

ErC50

> 1000 mg/l

72

Acute crustacea toxicity

EC50

> 1000 mg/l

Pseudokirchnerella subcapitata Daphnia magna

12.2. Persistence and degradability Abbiotic degradation (Hydrolysis, Photolysis) : Not applicable Physicochemical elimination (Oxidation, Hydrolysis) : Not applicable Photochemical elimination (Photooxidation) : no data available Biodegradation : hydrocarbons, C11-C12, isoalkanes, <2% aromatics : Not readily biodegradable ( 31,3 % after 28 days). - OECD 301E, C.4-B Revision No: 1,14

GB - EN

Revision date: 13.02.2012

48

Safety Data Sheet ACMOS CHEMIE KG

according to Regulation (EC) No 1907/2006

ACMOSIL 36-4142 Issue date : 15.02.2013

Page 11 of 14

12.3. Bioaccumulative potential Partition coefficient n-octanol /water (log Pow) : Not applicable (Preparation) Bioconcentration factor (BCF) : Not applicable (Preparation) 12.4. Mobility in soil Surface tension : no data available Transport soil-water (Adsorption coefficient) : The product is insoluble and floats on water. Transport water-air (volatility rate, Henry-constant) : The product evaporates slowly. Transport soil-air (volatility rate) : The product evaporates slowly.

This product contains one or more hydrocarbon UVCB's. Standard tests for this endpoint are intended for single substances and are not appropriate for this complex substance. 12.5. Results of PBT and vPvB assessment The product is neither a PBT- or vPvB-substance nor it contains PBT or VPvB substances. 12.6. Other adverse effects Ozone depletion potential (ODP) : no data available Photochemical ozone building potential (OBP) : no data available Global warming potential (GWP) : no data available

Product does not contain any organic halogens. (AOX)

SECTION 13: Disposal considerations 13.1. Waste treatment methods Advice on disposal Disposal according to offical regulations. Do not flush into surface water or sanitary sewer system. Do not dispose of waste into sewer. May not be disposed or deposited together with domestic garbage. Pack product waste or close and label uncleaned empty packages in respect to the local and official regulations and supply to an appropriate way of disposal. The relation of waste-codes according to EWC has to be realized by branch and process. The waste producer is resposible for correct coding and designation of his wastes. For small amounts (< 20 kg/L) next special waste counter or a mobile service for harmful substances. Before discharge in public drains (e.g. residues of washing- and rinsing liquids) please observe the relevant regulations. In case of further questions please your waste- or environmental representative or the responsible authority. List of proposed waste codes / waste designations in accordance with EWC : Waste disposal number of waste from residues/unused products WASTES FROM ORGANIC CHEMICAL PROCESSES; wastes from the MFSU of plastics, synthetic rubber 070204 and man-made fibres; other organic solvents, washing liquids and mother liquors Classified as hazardous waste. Waste disposal number of used product WASTES FROM ORGANIC CHEMICAL PROCESSES; wastes from the MFSU of plastics, synthetic rubber 070204 and man-made fibres; other organic solvents, washing liquids and mother liquors Classified as hazardous waste. Waste disposal number of contaminated packaging WASTE PACKAGING; ABSORBENTS, WIPING CLOTHS, FILTER MATERIALS AND PROTECTIVE 150110 CLOTHING NOT OTHERWISE SPECIFIED; packaging (including separately collected municipal packaging waste); packaging containing residues of or contaminated by dangerous substances Classified as hazardous waste. Contaminated packaging Contaminated packages must be completely emptied and may be reused after proper cleaning. Dipose of packages that cannot be cleaned like the product. Cleaning by recycling company. As well uncleaned (empty) containers remain contaminated by product residues and may be hazardous by vapours. They have to be disposed by specialists or have to be supplied to a licensed reconditioning. The conditions of the regional reconditioning companies have to be observed. Revision No: 1,14

GB - EN

Revision date: 13.02.2012

Safety Data Sheet ACMOS CHEMIE KG

according to Regulation (EC) No 1907/2006

ACMOSIL 36-4142 Issue date : 15.02.2013

Page 12 of 14

Offer rinsed packaging material to local recycling facilities . Recommended cleansing agent : Clean with detergents. Avoid solvents. Dispose of rinse water as waste water. Do not contaminate water.

SECTION 14: Transport information Land transport (ADR/RID) Other applicable information (land transport) Not classified as dangerous in the meaning of transport regulations. Inland waterways transport (ADN) Other applicable information (inland waterways transport) Not relevant Marine transport (IMDG) Other applicable information (marine transport) Not classified as dangerous in the meaning of transport regulations. Air transport (ICAO) Other applicable information (air transport) Not classified as dangerous in the meaning of transport regulations. 14.5. Environmental hazards

Dangerous for the environment:

no

14.6. Special precautions for Not relevant 14.7. Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code Not relevant Other applicable information Not relevant

SECTION 15: Regulatory information 15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture EU regulatory information

1999/13/EC (VOC):

Content of volatile organic compounds (VOC) = 78 % w/w. VOC-value (25 °C) = 626 g/L.

Additional information Regulation (EC) No 2037/2000 - Substances that deplete the ozone layer : Not applicable Regulation (EC) No 648/2004 and No 907/2006 - Detergents : Not applicable Regulation (EC) No 850/2004 - Persistent organic pollutants : Not applicable Regulation (EC) No 689/2008 - Export and import of dangerous chemicals : Not applicable Regulation (EC) No 552/2009 - Restriction of chemicals (REACH) as regards annex XVII : Not applicable

Authorisation of Chemicals (REACH) as regards Annex XIV : Not applicable Directive 2004/42/EC - Use of organic solvents in certain paints and lacquers : Not applicable Directive 96/82/EC - Control of major accident hazards involving dangerous substances (Seveso II), as last amended by Directive 2003/105/EC : Not applicable EC-Chemical inventories : All ingredients are listed in EINECS / ELINCS or excepted from listing. A chemical safety assessment (CSA) has been carried out on following substance(s) : hydrocarbons, C11-C12, isoalkanes, <2% aromatics, EC-No. : 918-167-1 Revision No: 1,14

GB - EN

Revision date: 13.02.2012

Safety Data Sheet ACMOS CHEMIE KG

according to Regulation (EC) No 1907/2006

ACMOSIL 36-4142 Issue date : 15.02.2013

Page 13 of 14

National regulatory information

Employment restrictions: Water contaminating class (D):

Observe employment restrictions for young people. Observe employment restrictions for child bearing mothers and nursing. 1 - slightly water contaminating

Additional information International chemical inventories (Registration status on substances) : no data available

European product inventories (Registration status on mixtures) : Istituto Superiore di Sanità / Archivio Preparati Pericolosi - ISS (http://www.preparatipericolosi.iss.it/iss/index.phtml) : This product was ed. Kemikalieinspektionen / Produktregistret / Swedish Chemicals Inspectorate - KemI (http://apps.kemi.se/nclass/default.asp) : This product was ed. Schweizerische Eidgenossenschaft - Bundesamt für Gesundheit - BAG (http://www.bag..ch) / Informationssystem für gefährliche und umweltrelevante Stoffe - IGS (http://igs.naz.ch/index.html) : This product was ed.

SECTION 16: Other information Changes This version replaces all former issues.

Changes made in this revision see section : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16. Disclaimer : The information is based on present level of our knowledge. It does not, however, give assurances of product properties and establishes no contract legal rights. The information given is designed only as a guidance for safe handling, use, processing, storage, transportation, disposal and release The receiver of our product is singulary responsible for adhering to existing laws and regulations. All descriptions are approximate values, they are not specified for construction of specifications. This safety data sheet does not represent any operating instruction according to national chemical regulations. It may be used for creation, but must not replace it. The employer is not relieved from his duties. All technical information to occupational protection are directed predominately to experts first (safety engineers, occupational medicines). Abbreviations and acronyms CAS: Chemical Abstracts Service. DNEL: Derived No-Effect Level. EC50: Effective concentration, 50 percent. EC: European community. EINECS: European Inventory of Existing Commercial Chemical Substances. ELINCS: European List of Notified Chemical Substances. IC50 / ErC50: Inhibitory concentration, 50 percent. EN: European standard. FDA: US-Food and Drug istration. GHS: Globally Harmonized System of Classification and Labelling of Chemicals. ISO: A standard of International Standards Organisation. LC50: Lethal concentration, 50 percent. LD50: Lethal Dose, 50 percent. log Kow (Pow): octanol-water partition coefficient. OECD: Organisation for Economic Co-operation and Development. PBT: Persistent, bioaccumulabe and toxic. PNEC: Predicted No-Effect Concentration. UN: United Nations. vPvB: Very persistent and very bioaccumulable.

Revision No: 1,14

GB - EN

Revision date: 13.02.2012

Safety Data Sheet ACMOS CHEMIE KG

according to Regulation (EC) No 1907/2006

ACMOSIL 36-4142 Issue date : 15.02.2013

Page 14 of 14

Full text of R phrases referred to under Sections 2 and 3 53 May cause long-term adverse effects in the aquatic environment. 65 Harmful: may cause lung damage if swallowed. 66 Repeated exposure may cause skin dryness or cracking. Full text of H statements referred to under Sections 2 and 3 H304 May be fatal if swallowed and enters airways. H413 May cause long lasting harmful effects to aquatic life . Further Information Full text of all R-phrases which are referred to in section 2 and 3 of this safety data sheet - see previous list. These (this) R-phrases/R-phrases apply/applies to the substance(s) of content, however, it does not necessarily show the classification of the product.

Training references : Yearly briefing and instruction of employees by means of operating instructions according to article 8 of EC-directive 98/24/EC. Recommended restriction of application : For more reference to application see separate product information. Please refer to our internet website for more information. Sources of most important data used for creation of the data sheet : The classification corresponds to current EC-lists, but is completed by statements of technical literature and company data. Other public accessible sources : Regulation (EC) No. 1907/2006 (REACH) in the valid version in each case Regulation (EC) No. 1272/2008 (CLP) in the valid version in each case Substance Directive 67/548/EEC in the valid version in each case Preparation Directive 1999/45/EC in the valid version in each case European Agency for Safety and Health at Work - national air treshold values from european member states - EH 40 (http://osha.europa.eu/good_practice/topics/dangerous_substances/oel/.stm) European Chemical Substances Information System - ESIS (http://ecb.jrc.ec.europa.eu/esis) MERCK Chemical Databases - MERCK Chemicals (http://www.merck-chemicals.com) Further information and practical guides on the internet : European Chemicals Agency - ECHA (http://ec.europa.eu/echa) The access to European Union law - EUR-Lex (http://eur-lex.europa.eu) Control of Substances Hazardous to Health Regulations - COSHH (http://www.coshh-essentials.org.uk/Home.asp) Pollution Prevention and Control Act and Pollution Prevention and Control Regulations Health and Safety Executive - HSE - Leaflets for Chemicals (http://www.hse.gov.uk/pubns/chindex.htm) Classification of mixtures and used evaluation methods in accordance with Regulation (EC) No 1272/2008 (CLP) : The transition period according to CLP-Regulation (Article 61) has not been expired yet. Inquiry office : Laboratory (Division : Occupational- /Product security) person : Mr. Dryhaus (Telephone : +49-421-5189-0, Telefax : +49-421-5189-871) Office hours : Mo - Th from 7.30 - 16.15 h and Fr from 7.30 - 13.30 h. Out of office hours no call diversion.

Revision No: 1,14

GB - EN

Revision date: 13.02.2012