Aatcc-127-water-resistance-hydrostatic-pressure-test.pdf 3e6m3g

AATCC takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this test method. s of this test method are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This test method is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reaffirmed or withdrawn. Your comments are invited either for revision of this test method or for additional methods and should be addressed to the AATCC Technical Center. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing, you should make your views known to Amy G. Hammonds, Laboratory Director, at the address shown below. This test method is copyrighted by AATCC, PO Box 12215, Research Triangle Park, NC 27709 USA. Individual reprints (single or multiple copies) of this method may be obtained by ing AATCC at the above address or tel: 919-549-3526; fax: 919-549-8933, or e-mail: [email protected]. AATCC License Agreement: This test method is copyrighted by the American Association of Textile Chemists and Colorists (AATCC), PO Box 12215, 1 Davis Drive, Research Triangle Park, NC USA. All rights reserved. AATCC grants you a license as follows: The right to an electronic file of this AATCC test method for temporary storage on one computer for purposes of viewing, and/or printing one copy of the AATCC test method for individual use. Neither the electronic file nor the hard copy print may be reproduced in any way. In addition, the electronic file may not be distributed elsewhere over computer networks or otherwise. The hard copy print may only be distributed to other employees for their internal use within your organization. This test method is not for resale.

Copyright The American Association of Textile Chemists and Colorists Provided by IHS under license with AATCC No reproduction or networking permitted without license from IHS

--`,,```,,,,````-`-`,,`,,`,`,,`---

标准分享网　ｗｗｗ．ｂｚｆｘｗ．ｃｏｍ　免费下载

Not for Resale

AATCC Test Method 127-2003

TESTEX Textile Instrument Ltd Offers a wide range of textile testing equipment with european quality and chinese price,kindly us for more information. Web : www.textileinstruments.net Email: [email protected]

Water Resistance: Hydrostatic Pressure Test Developed in 1968 by AATCC Committee RA63; reaffirmed 1971, 1974, 1977, 1980, 1989, 2003; editorially revised 1982, 1986; editorially revised and reaffirmed 1985; revised 1995, 1998. Related to ISO 811. 1. Purpose and Scope

1.1 This test method measures the resistance of a fabric to the penetration of water under hydrostatic pressure. It is applicable to all types of fabrics, including those treated with a water resistant or water repellent finish. 1.2 Water resistance depends on the repellency of the fibers and yarns, as well as the fabric construction. 1.3 The results obtained by this method may not be the same as the results obtained by the AATCC methods for resistance to rain or water spray. 2. Principle

2.1 One surface of the test specimen is subjected to a hydrostatic pressure, increasing at a constant rate, until three points of leakage appear on its other surface. The water may be applied from above or below the test specimen. 3. Terminology

3.1 hydrostatic pressure, n.—the force distributed over an area exerted by water. 3.2 water resistance, n.—of fabric, the characteristic to resist wetting and penetration by water. 3.3 water repellency, n.—of fabric, in textiles, the characteristic of fiber, yarn, or fabric to resist wetting. 4. Safety Precautions

NOTE: These safety precautions are for information purposes only. The precautions are ancillary to the testing procedures and are not intended to be all inclusive. It is the ’s responsibility to use safe and proper techniques in handling materials in this test method. Manufacturers MUST be consulted for specific details, such as material safety data sheets and other manufacturer’s recommendations. All OSHA standards and rules must also be consulted and followed. 4.1 Good laboratory practices should be followed. Wear safety glasses in all laboratory areas. 4.2 Manufacturer’s safety recommendations should be followed when operating laboratory testing equipment.

5. Apparatus and Materials

5.1 Hydrostatic Tester. 5.1.1 For Option 1, Hydrostatic Pressure Tester (see 11.1). 5.1.2 For Option 2, Hydrostatic Head Tester (see 11.2). 5.2 Water, distilled or de-ionized. 6. Test Specimens

6.1 A minimum of three fabric specimens should be taken diagonally across the width of the fabric to be representative of the material. Cut specimens at least 200 × 200 mm to allow proper clamping. 6.2 Handle the specimens as little as possible and avoid folding or contaminating the area to be tested. 6.3 Condition the test specimens at 21 ± 2°C (70 ± 5°F) air at 65 ± 2% RH for at least 4 h before testing. 6.4 The surface of the fabric to be exposed to water must be specified because different results may be obtained on the face and the back. Identify that surface on a corner of each specimen. 7. Procedure

7.1 the water in with the test specimen is regulated at 21 ± 2°C (70 ± 5°F) (see 10.3). 7.2 Dry the clamping surface. 7.3 Clamp the specimen with the surface to be tested facing the water (see 11.5). 7.4 Operation. 7.4.1 Option 1—Hydrostatic Pressure Tester (see 11.1). 7.4.1.1 Turn on the motor, press the lever to raise the overflow device at the rate of 10 mm/s, and close the air vent as soon as water flows from it. 7.4.2 Option 2—Hydrostatic Head Tester (see 11.2). 7.4.2.1 Select the gradient of 60 mbar/ min, press the start button (see 11.4). 7.5 Disregarding water droplets that appear within approximately 3 mm adjacent to the edge of the specimen clamping ring, record the hydrostatic pressure at the moment water droplets penetrate the fabric in three different places.

10. Precision and Bias

10.1 Precision. The test results are tester dependent. Precision statements for each tester are given in 10.2 and 10.3. 10.2 Suter Hydrostatic Pressure Tester (Option 1). 10.2.1 In 1993, a limited interlaboratory study was completed, which included six laboratories, two operators in each, running determinations on three specimens of two fabrics. No prior assessment was made of the relative level of the participating laboratories on performance of the test method. 10.2.2 The two fabrics were at different levels (Fabric 1 approximately 810 mm and Fabric 2 approximately 340 mm), and residual variances of the two fabrics were found to be different. Accordingly, precision is reported separately for each fabric. 10.2.3 s of the method are advised of the limited nature of this study and advised to apply these findings with due caution. 10.2.4 Analysis of the data sets for each fabric yielded components of variance and critical differences as displayed in Tables I, II and III. Differences between two averages of (N) determinations, for the appropriate precision parameter, should reach or exceed the table value to be statistically significant at the 95% confidence level. Table I—Components of Variance for Two Fabrics (Option 1 Tester) Component Laboratory Operator Specimen

Variance Fabric 1

Variance Fabric 2

13.450 3.127 30.253

7.323 2.145 5.382

8. Calculation

Table II—Fabric 1—Critical Differences — 95% Confidence (Option 1 Tester)

8.1 Calculate the average hydrostatic pressure for each sample.

Det in Single Within Between Avg (N) Operator Laboratory Laboratory

9. Report

9.1 Results for each specimen and the average for each sample.

1 2 3 4 5

15.25 10.78 8.80 7.62 6.82

16.02 11.84 10.08 9.06 8.04

TM 127-2003

AATCC Technical Manual /2006 --`,,```,,,,````-`-`,,`,,`,`,,`---

Copyright The American Association of Textile Chemists and Colorists Provided by IHS under license with AATCC No reproduction or networking permitted without license from IHS

9.2 The material and the side tested. 9.3 Water temperature and type. 9.4 Gradient (rate of increasing water pressure). 9.5 Tester option used. 9.6 Any modification to the method.

Not for Resale

18.97 15.61 14.31 13.62 13.19

211

Table III—Fabric 2—Critical Differences—95% Confidence (Option 1 Tester) Det in Avg (N)

Single Within Between Operator Laboratory Laboratory

1 2 3 4 5

6.43 4.55 3.71 3.22 2.88

7.61 6.10 5.50 5.18 4.98

10.68 9.67 9.30 9.12 9.00

Table V—Material B—Critical Differences—95% Confidence (Option 2 Tester) Det in Avg (N)

Single Operator

Within Laboratory

1 2 3 4 5

10.08 7.13 5.82 5.04 4.51

12.85 9.09 7.42 6.43 5.75

Until such precision information is available, s of this method should use standard statistical techniques in making any comparison of test results for between laboratory averages. 10.4 Bias. 10.4.1 Water resistance of fabrics can only be defined in of a test method. There is no independent, referee method for determining the true value. This test method has no known bias. 11. Notes

--`,,```,,,,````-`-`,,`,,`,`,,`---

10.3 Textest FX3000 Hydrostatic Head Tester (Option 2). 10.3.1 In a single-laboratory study, six different laboratory technicians run determinations on three specimens of five materials. 10.3.2 The five materials were at different levels of approximately: A=103, B=33, C=37, D=12, and E=77. Data obtained in this study is recorded in millibars (SI standard). The residual variance of the five materials were found to be different, therefore, precision is reported separately for each. 10.3.3 Analysis of the data sets for each material yielded critical differences as shown in Tables IV, V, VI, VII and VIII. Differences between two averages of (N) determinations, for the appropriate precision parameter, should reach or exceed the table value to be statistically significant at the 95% confidence level. 10.3.4 Between laboratory precision has not been established for this option.

Table IV—Material A—Critical Differences—95% Confidence (Option 2 Tester)

Table VI—Material C—Critical Differences—95% Confidence (Option 2 Tester) Det in Avg (N)

Single Operator

Within Laboratory

1 2 3 4 5

16.13 11.40 9.31 8.06 7.21

16.13 11.40 9.31 8.06 7.21

Table VII—Material D—Critical Differences—95% Confidence (Option 2 Tester) Det in Avg (N)

Single Operator

Within Laboratory

1 2 3 4 5

2.88 2.04 1.66 1.44 1.29

3.50 2.47 2.02 1.75 1.57

Table VIII—Material E—Critical Differences—95% Confidence (Option 2 Tester)

Det in Avg (N)

Single Operator

Within Laboratory

Det in Avg (N)

Single Operator

Within Laboratory

1 2 3 4 5

72.49 51.26 41.85 36.25 32.42

72.49 51.26 41.85 36.25 32.42

1 2 3 4 5

15.04 10.63 8.68 7.52 6.72

16.55 11.70 9.55 8.27 7.40

212

TM 127-2003

Copyright The American Association of Textile Chemists and Colorists Provided by IHS under license with AATCC No reproduction or networking permitted without license from IHS

11.1 Hydrostatic Pressure Tester (Suter). 11.1.1 The apparatus consists essentially of an inverted conical well equipped with a coaxial ring clamp to fasten the cloth specimen under the well bottom. The apparatus introduces water from above the specimen over an area 114 mm in diameter and at a rate of 10.0 ± 0.5 mm of hydrostatic head per second. A mirror is affixed below the specimen to enable the operator to ascertain penetration of the specimen by drops of water. A valve is provided for venting the air in the well. 11.1.2 Hydrostatic testing apparatus of the type described is available from Alfred Suter Co., P.O. Box 350, Ramsey NJ 07446-0350; tel: 201/818-0113; fax: 201/818-0654. 11.2 Hydrostatic Head Tester (Textest). 11.2.1 Uses an electronically controlled pump to apply hydrostatic pressure at 60 mbar/min (selectable) to the bottom side of the fabric. A reservoir with a circular test area of 100 ± 5 cm2 (»4.5 in. diam) contains distilled or deionized water which is applied to the fabric surface. The fabric specimen is secured with a coaxial clamp which is equipped with viewing lamps to aid the operator in seeing the penetration of water droplets. A digital readout displays the pressure. An RS232 data port is provided to transfer the test results for storage and statistical analysis. 11.2.2 The Textest Hydrostatic Head Tester is available from Advanced Testing Instruments Corp., 316D Business Parkway, Greer SC 29651-7119; tel: 864/989-0566; fax: 864/ 989-0567. 11.3 Some laboratories use water at ambient temperature. If testing is performed other than 21 ± 2°C, so state. 11.4 1 mbar = 1.02 cm H2O. 11.5 Lateral water leakage can be minimized by sealing the fabric with paraffin at the clamping area.

AATCC Technical Manual/2006 Not for Resale