44608p40 69b58

查询44608P40供应商

捷多邦，专业PCB打样工厂，24小时加急出货

MC44608 Few External Components Reliable and Flexible GreenLine Very High Voltage PWM Controller The MC44608 is a high performance voltage mode controller designed for off–line converters. This high voltage circuit that integrates the start–up current source and the oscillator capacitor, requires few external components while offering a high flexibility and reliability. The device also features a very high efficiency stand–by management consisting of an effective Pulsed Mode operation. This technique enables the reduction of the stand–by power consumption to approximately 1W while delivering 300mW in a 150W SMPS. • Integrated Start–Up Current Source • Lossless Off–Line Start–Up • Direct Off–Line Operation • Fast Start–Up

http://onsemi.com

8 1 DIP–8 P SUFFIX CASE 626

PIN CONNECTIONS AND MARKING DIAGRAM

General Features

Flexibility Duty Cycle Control Undervoltage Lockout with Hysteresis On Chip Oscillator Switching Frequency 40, or 75kHz Secondary Control with Few External Components

Demag

1

8

Isense

2

7

Control Input

3

Gnd

4

44608Pxxx AWL YYWW

• • • • •

Vi

6

Vcc

5

Driver

Protections

• • • • • •

Programmable Low Inertia Over Voltage Protection Against Open Loop Internal Thermal Protection

GreenLine Controller

• Pulsed Mode Techniques for a Very High Efficiency Low Power • •

AWL = Manufacturing Code YYWW = Date Code

Maximum Duty Cycle Limitation Cycle by Cycle Current Limitation Demagnetization (Zero Current Detection) Protection “Over VCC Protection” Against Open Loop

Mode Lossless Startup Low dV/dT for Low EMI Radiations

(Top View)

ORDERING INFORMATION Device

Switching Package Frequency

Shipping

MC44608P40

40kHz

Plastic DIP–8

50 / Rail

MC44608P75

75kHz

Plastic DIP–8

50 / Rail

MC44608 REPRESENTATIVE BLOCK DIAGRAM Demag

Vi

1 DMG

+ –

8 UVLO2

50 mV /20 mV

>24 mA

>120 m A

9 mA

Start–up Source

Latched off Phase Demag Logic

1

Start–up Phase

Output Start–up Phase 200 m A Switching Phase 0

& OSC Enable

Stand–by Management

Leading Edge Blanking

Output

2 Isense

+ –

&

&

5 Driver 4

VPWM

+ CS – 1V

Buffer

Thermal S Shutdown PWM Latch R Q

& PWM

OC NOC

V CC

OUT Disable DMG

Clock OSC

6

OVP UVLO1 UVLO2

2 mS

Start–up Phase

S1 & Stand–by

Switching Phase

Latched off Phase

V CC Management

4 kHz Filter

GND Latched off Phase & Stand–by S2 S3 Regulation Block Switching Phase

3 Control Input

MAXIMUM RATINGS Rating

Symbol

Value

Unit

Total Power Supply Current

ICC

30

mA

Output Supply Voltage with Respect to Ground

VCC

16

V

Vinputs

–1.0 to +16

V

Vi

500

V

600 100

mW °C/W

Operating Junction Temperature

PD RθJA TJ

150

°C

Operating Ambient Temperature

TA

–25 to +85

°C

All Inputs except Vi Line Voltage Power Dissipation and Thermal Characteristics Maximum Power Dissipation at TA = 85°C Thermal Resistance, Junction–to–Air

MC44608 ELECTRICAL CHARACTERISTICS Characteristic

Symbol

Min

Typ

Max

ROL ROH

5.0

8.5 15

15

OUTPUT SECTION

Unit

W

Output Resistor Sink Resistance Source Resistance Output Voltage Rise Time (from 3 V up to 9 V) (1)

tr

50

ns

Output Voltage Falling Edge Slew–Rate (from 9 V down to 3 V) (1)

tf

50

ns

CONTROL INPUT SECTION Duty Cycle @ Ipin3 = 2.5 mA

d2mA

Duty Cycle @ Ipin3 = 1.0 mA

d1mA

Control Input Clamp Voltage (Switching Phase) @ Ipin3 = –1.0 mA

2.0

%

36

43

48

%

4.75

5.0

5.25

V

Latched Phase Control Input Voltage (Stand–by) @ Ipin3 = +500 mA

VLP–stby

3.4

3.9

4.3

V

Latched Phase Control Input Voltage (Stand–by) @ Ipin3 = +1.0 mA

VLP–stby

2.4

3.0

3.7

V

VCS–th

0.95

1.0

1.05

IB–cs

–1.8

ICS–stby

180

200

220

ICS–stup

180

200

220

CURRENT SENSE SECTION Maximum Current Sense Input Threshold Input Bias Current Stand–By Current Sense Input Current Start–up Phase Current Sense Input Current Propagation Delay (Current Sense Input to Output @ VTH T MOS = 3 V)

1.8

V

mA mA mA

TPLH(In/Out)

220

ns

Leading Edge Blanking Duration

MC44608P40

TLEB

480

ns

Leading Edge Blanking Duration

MC44608P75

TLEB

250

ns

Leading Edge Blanking Duration

MC44608P100

TLEB

200

ns

Leading Edge Blanking + Propagation Delay

MC44608P40

TDLY

500

680

900

ns

Leading Edge Blanking + Propagation Delay

MC44608P75

TDLY

370

470

570

ns

Leading Edge Blanking + Propagation Delay

MC44608P100

TDLY

400

ns

OSCILLATOR SECTION Normal Operation Frequency MC44608P40

fosc

36

Normal Operation Frequency MC44608P75

fosc

68

Normal Operation Frequency MC44608P100

fosc

Maximum Duty Cycle @ f = fosc

dmax

40

44

kHz

75

82

kHz

100 78

82

kHz 86

%

OVERVOLTAGE SECTION

Quick OVP Input Filtering (Rdemag = 100 kW) Propagation Delay (Idemag > Iovp to output low) Quick OVP Current Threshold Protection Threshold Level on VCC Minimum Gap Between VCC–OVP and Vstup–th

Tfilt

250

TPHL(In/Out)

ns µs

2.0

IOVP

105

120

140

µA

VCC–OVP

14.8

15.3

15.8

V

VCC–OVP – Vstup

1.0

NOTES: (1) This parameter is measured using 1.0 nF connected between the output and the ground.

V

MC44608 ELECTRICAL CHARACTERISTICS (VCC = 12 V, for typical values TA = 25°C, for min/max values TA = –25°C to +85°C unless otherwise noted) (Note 1) Characteristic

Symbol

Min

Typ

Max

Unit

Vdmg–th

30

50

69

mV

DEMAGNETIZATION DETECTION SECTION (Note 2) Demag Comparator Threshold (Vpin1 increasing) Demag Comparator Hysteresis (Note 3)

Hdmg

Propagation Delay (Input to Output, Low to High)

30

tPHL(In/Out)

Input Bias Current (Vdemag = 50 mV)

mV

300

ns

mA

Idem–lb

–0.6

Negative Clamp Level (Idemag = –1 mA)

Vcl–neg–dem

–0.9

–0.7

–0.4

V

Positive Clamp Level @ Idemag = 125 mA

Vcl–pos– dem–H

2.05

2.3

2.8

V

Positive Clamp Level @ Idemag = 25 mA

Vcl–pos– dem–L

1.4

1.7

1.9

V

OVERTEMPERATURE SECTION Trip Level Over Temperature

Thigh

160

°C

Hysteresis

Thyst

30

°C

STAND–BY MAXIMUM CURRENT REDUCTION SECTION Normal Mode Recovery Demag Pin Current Threshold

Idem–NM

20

25

30

mA

K FACTORS SECTION FOR PULSED MODE OPERATION ICCS / Istup

MC44608P40

10 x K1

2.4

2.9

3.8

–

ICCS / Istup

MC44608P75

10 x K1

2.8

3.3

4.2

–

MC44608P100

10 x K1

ICCS / Istup

3.5

–

103 x K2

46

52

63

–

(Vstup – UVLO2) / (Vstup – UVLO1)

102 x Ksstup

1.8

2.2

2.6

–

(UVLO1 – UVLO2) / (Vstup – UVLO1)

102 x Ksl 106 x Ycstby

90

120

150

–

175

198

225

–

Dmgr

3.0

4.7

5.5

–

ICCL / Istup

ICS / Vcsth Demag ratio Iovp / Idem NM (V3 1 mA – V3 0.5 mA) / (1 mA – 0.5 mA)

R3

1800

W

Vcontrol Latch–off

V3

4.8

V

SUPPLY SECTION Minimum Start–up Voltage

Vilow

VCC Start–up Voltage Output Disabling VCC Voltage After Turn On Hysteresis (Vstup–th – Vuvlo1)

Vstup–th

12.5

Vuvlo1

9.5

Hstup–uvlo1

VCC Undervoltage Lockout Voltage

Vuvlo2

Hysteresis (Vuvlo1 – Vuvlo2)

50

V

13.1

13.8

V

10

10.5

V

3.1 6.2

Huvlo1–uvlo2

6.6

V 7.0

3.4

V V

Absolute Normal Condition VCC Start Current @ (Vi = 100 V) and (VCC = 9 V)

–(ICC)

7.0

9.5

12.8

mA

Switching Phase Supply Current (no load)

ICCS

2.0 2.4 –

2.6 3.2 3.4

3.6 4.0 –

mA

ICC–latch

0.3

0.5

0.68

mA

Latched Off Phase Supply Current Hiccup Mode Duty Cycle (no load)

MC44608P40 MC44608P75 MC44608P100

dHiccup

10

%

NOTES: (1) Adjust VCC above the start–up threshold before setting to 12 V. Low duty cycle pulse techniques are used during test to maintain junction temperature as close to ambient as possible. (2) This function can be inhibited by connecting pin 1 to GND. (3) Guaranteed by design (non tested)

MC44608 PIN FUNCTION DESCRIPTION Pin

Name

Description

1

Demag

The Demag pin offers 3 different functions: Zero voltage crossing detection (50mV), 24µA current detection and 120µA current detection. The 24µA level is used to detect the secondary reconfiguration status and the 120µA level to detect an Over Voltage status called Quick OVP.

2

Isense

The Current Sense pin senses the voltage developed on the series resistor inserted in the source of the power MOSFET. When Isense reaches 1V, the Driver output (pin 5) is disabled. This is known as the Over Current Protection function. A 200µA current source is flowing out of the pin 3 during the start–up phase and during the switching phase in case of the Pulsed Mode of operation. A resistor can be inserted between the sense resistor and the pin 3, thus a programmable peak current detection can be performed during the SMPS stand–by mode.

3

Control Input

A current from the secondary side of the SMPS via the opto–coupler is injected into this pin. A resistor can be connected between this pin and GND to allow the programming of the Burst duty cycle during the Stand–by mode.

4

Ground

5

Driver

The current and slew rate capability of this pin are suited to drive Power MOSFETs.

6

VCC

This pin is the positive supply of the IC. The driver output gets disabled when the voltage becomes higher than 15V and the operating range is between 6.6V and 13V. An intermediate voltage level of 10V creates a disabling condition called Latched Off phase.

This pin is the ground of the primary side of the SMPS.

7

This pin is to provide isolation between the Vi pin 8 and the VCC pin 6.

8

Vi

This pin can be directly connected to a 500V voltage source for start–up function of the IC. During the Start–up phase a 9 mA current source is internally delivered to the VCC pin 6 allowing a rapid charge of the VCC capacitor. As soon as the IC starts–up, this current source is disabled.

OPERATING DESCRIPTION Regulation V LP–stby

V CC Control Input

1 S3

0

1 S2

0

Stand–by Latched off Phase

&

3

PWM Latch

V dd 20 W

5V

Switching Phase

The switch S3 is closed in Stand–by mode during the Latched Off Phase while the switch S2 remains open. (See section PULSED MODE DUTY CYCLE CONTROL). The resistor Rdpulsed (Rduty cycle burst) has no effect on the regulation process. This resistor is used to determine the burst duty cycle described in the chapter “Pulsed Duty Cycle Control” on page 8.

PWM Regulation Comparator Output 4 kHz Filter 1.6 V

Figure 1. Regulator

The pin 3 senses the current provided by the opto coupler. During the switching phase the switch S2 is closed and the shunt regulator is accessible by the pin 3. The shunt regulator voltage is typically 5V. The dynamic resistance of the shunt regulator represented by the zener diode is 20W. The gain of the Control input is given on Figure 10 which shows the duty cycle as a function of the current injected into the pin 3. A 4kHz filter network is inserted between the shunt regulator and the PWM comparator to cancel the high frequency residual noise.

The MC44608 works in voltage mode. The on–time is controlled by the PWM comparator that compares the oscillator sawtooth with the regulation block output (refer to the block diagram on page 2). The PWM latch is initialized by the oscillator and is reset by the PWM comparator or by the current sense comparator in case of an over current. This configuration ensures that only a single pulse appears at the circuit output during an oscillator cycle. Current Sense

The inductor current is converted to a positive voltage by inserting a ground reference sense resistor RSense in series with the power switch. The maximum current sense threshold is fixed at 1V. The peak current is given by the following equation: Ipk max

1 + Rsense (A) (W )

MC44608 In stand–by mode, this current can be lowered as due to the activation of a 200µA current source:

Oscillator Buffer Output

cs(kW) 0, 2) (A) Ipk + * (RRsense max *stby (W )

R Q DMG S

1

Demag

200 m A 1

DMG STAND–BY

&

0

&

50/20 mV > 24 m A >120 m A

START–UP

1

+ – Idemag

Switching Phase

Idemag

Current Mirror

Isense Rcs

L.E.B.

2

Overcurrent Comparator +

Figure 3. Demagnetization Block OC

–

Rsense

This function can be inhibited by grounding it but in this case, the quick and programmable OVP is also disabled.

1V

Oscillator Figure 2. Current Sense

The current sense input consists of a filter (6kW, 4pF) and of a leading edge blanking. Thanks to that, this pin is not sensitive to the power switch turn on noise and spikes and practically in most applications, no filtering network is required to sense the current. Finally, this pin is used: – as a protection against over currents (Isense > I) – as a reduction of the peak current during a Pulsed Mode switching phase. The overcurrent propagation delay is reduced by producing a sharp output turn off (high slew rate). This results in an abrupt output turn off in the event of an over current and in the majority of the pulsed mode switching sequense.

The MC44608 contains a fixed frequency oscillator. It is built around a fixed value capacitor CT succesively charged and discharged by two distinct current sources ICH and IDCH. The window comparator senses the CT voltage value and activates the sources when the voltage is reaching the 2.4V/4V levels. ICH DMG from Demag logic block

OSC

SCH

&

4V 2.4 V

Window + comp

Clock

–

SDCH IDCH

CT

Demagnetization Section

The MC44608 demagnetization detection consists of a comparator designed to compare the VCC winding voltage to a reference that is typically equal to 50mV. This reference is chosen low to increase effectiveness of the demagnetization detection even during start–up. A latch is incorporated to turn the demagnetization block output into a low level as soon as a voltage less than 50 mV is detected, and to keep it in this state until a new pulse is generated on the output. This avoids any ringing on the input signal which may alter the demagnetization detection. For a higher safety, the demagnetization block output is also directly connected to the output, which is disabled during the demagnetization phase. The demagnetization pin is also used for the quick, programmable OVP. In fact, the demagnetization input current is sensed so that the circuit output is latched off when this current is detected as higher than 120µA.

Figure 4. Oscillator Block

The complete demagnetization status DMG is used to inhibit the recharge of the CT capacitor. Thus in case of incomplete transformer demagnetization the next switching cycle is postpone until the DMG signal appears. The oscillator remains at 2.4V corresponding to the sawtooth valley voltage. In this way the SMPS is working in the so called SOPS mode (Self Oscillating Power Supply). In that case the effective switching frequency is variable and no longer depends on the oscillator timing but on the external working conditions (Refer to DMG signal in the Figure 5).

MC44608 OSC 4V

V

CC

13 V

Vcont 2.4 V

10 V

Clock

6.5 V

DMG

Start–up Phase

Latched off Phase

Switching Phase

Iprim

Figure 6. Hiccup Mode Figure 5.

The OSC and Clock signals are provided according to the Figure 5. The Clock signals correspond to the CT capacitor discharge. The bottom curve represents the current flowing in the sense resistor Rcs. It starts from zero and stops when the sawtooth value is equal to the control voltage Vcont. In this way the SMPS is regulated with a voltage mode control. Overvoltage Protection

The MC44608 offers two OVP functions: – a fixed function that detects when VCC is higher than 15.4V – a programmable function that uses the demag pin. The current flowing into the demag pin is mirrored and compared to the reference current Iovp (120µA). Thus this OVP is quicker as it is not impacted by the VCC inertia and is called QOVP. In both cases, once an OVP condition is detected, the output is latched off until a new circuit START–UP. Start–up Management

The Vi pin 8 is directly connected to the HV DC rail Vin. This high voltage current source is internally connected to the VCC pin and thus is used to charge the VCC capacitor. The VCC capacitor charge period corresponds to the Start–up phase. When the VCC voltage reaches 13V, the high voltage 9mA current source is disabled and the device starts working. The device enters into the switching phase. It is to be noticed that the maximum rating of the Vi pin 8 is 700V. ESD protection circuitry is not currently added to this pin due to size limitations and technology constraints. Protection is limited by the drain–substrate junction in avalanche breakdown. To help increase the application safety against high voltage spike on that pin it is possible to insert a small wattage 1kW series resistor between the Vin rail and pin 8. The Figure 6 shows the VCC voltage evolution in case of no external current source providing current into the VCC pin during the switching phase. This case can be encountered in SMPS when the self supply through an auxiliary winding is not present (strong overload on the SMPS output for example). The Figure 16 also depicts this working configuration.

In case of the hiccup mode, the duty cycle of the switching phase is in the range of 10%. Mode Transition

The LW latch Figure 7 is the memory of the working status at the end of every switching sequence. Two different cases must be considered for the logic at the termination of the SWITCHING PHASE: 1. No Over Current was observed 2. An Over Current was observed These 2 cases are corresponding to the signal labelled NOC in case of “No Over Current” and “OC” in case of Over Current. So the effective working status at the end of the ON time memorized in LW corresponds to Q=1 for no over current and Q=0 for over current. This sequence is repeated during the Switching phase. Several events can occur: 1. SMPS switch OFF 2. SMPS output overload 3. Transition from Normal to Pulsed Mode 4. Transition from Pulsed Mode to Normal Mode Latched Off Phase VPWM OUT

&

NOC OC

S

Q

R LEB out 1V

&

LW Q

+ CS –

&

S Q Stand–by & Mode R1 R2

S1 Switch

Start–up Idemag Switching Start–up Phase > 24 m A Phase Phase

Figure 7. Transition Logic • 1. SMPS SWITCH OFF

When the mains is switched OFF, so long as the bulk electrolithic bulk capacitor provides energy to the SMPS, the controller remains in the switching phase. Then the peak current reaches its maximum peak value, the switching frequency decreases and all the secondary voltages are reduced. The VCC voltage is also reduced. When VCC is equal to 10V, the SMPS stops working.

MC44608 • 2. Overload

In the hiccup mode the 3 distinct phases are described as follows (refer to Figure 6): The SWITCHING PHASE: The SMPS output is low and the regulation block reacts by increasing the ON time (dmax = 80%). The OC is reached at the end of every switching cycle. The LW latch (Figure 7) is reset before the VPWM signal appears. The SMPS output voltage is low. The VCC voltage cannot be maintained at a normal level as the auxiliary winding provides a voltage which is also reduced in a ratio similar to the one on the output (i.e. Vout nominal / Vout short–circuit). Consequently the VCC voltage is reduced at an operating rate given by the combination VCC capacitor value together with the ICC working consumption (3.2mA) according to the equation 2. When VCC crosses 10V the WORKING PHASE gets terminated. The LW latch remains in the reset status. The LATCHED–OFF PHASE: The VCC capacitor voltage continues to drop. When it reaches 6.5V this phase is terminated. Its duration is governed by equation 3. The START–UP PHASE is reinitiated. The high voltage start–up current source (–ICC1 = 9mA) is activated and the MODE latch is reset. The VCC voltage ramps up according to the equation 1. When it reaches 13V, the IC enters into the SWITCHING PHASE. The NEXT SWITCHING PHASE: The high voltage current source is inhibited, the MODE latch (Q=0) activates the NORMAL mode of operation. Figure 2 shows that no current is injected out pin 2. The over current sense level corresponds to 1V. As long as the overload is present, this sequence repeats. The SWITCHING PHASE duty cycle is in the range of 10%. • 3. Transition from Normal to Pulsed Mode

In this sequence the secondary side is reconfigured (refer to the typical application schematic on page 13). The high voltage output value becomes lower than the NORMAL mode regulated value. The TL431 shunt regulator is fully OFF. In the SMPS stand–by mode all the SMPS outputs are lowered except for the low voltage output that supply the wake–up circuit located at the isolated side of the power supply. In that mode the secondary regulation is performed by the zener diode connected in parallel to the TL431. The secondary reconfiguration status can be detected on the SMPS primary side by measuring the voltage level present on the auxiliary winding Laux. (Refer to the Demagnetization Section). In the reconfigured status, the Laux voltage is also reduced. The VCC self–powering is no longer possible thus the SMPS enters in a hiccup mode similar to the one described under the Overload condition. In the SMPS stand–by mode the 3 distinct phases are: The SWITCHING PHASE: Similar to the Overload mode. The current sense clamping level is reduced

according to the equation of the current sense section, page 5. The C.S. clamping level depends on the power to be delivered to the load during the SMPS stand–by mode. Every switching sequence ON/OFF is terminated by an OC as long as the secondary Zener diode voltage has not been reached. When the Zener voltage is reached the ON cycle is terminated by a true PWM action. The proper SWITCHING PHASE termination must correspond to a NOC condition. The LW latch stores this NOC status. The LATCHED OFF PHASE: The MODE latch is set. The START–UP PHASE is similar to the Overload Mode. The MODE latch remains in its set status (Q=1). The SWITCHING PHASE: The Stand–by signal is validated and the 200µA is sourced out of the Current Sense pin 2. • 4. Transition from Stand–by to Normal

The secondary reconfiguration is removed. The regulation on the low voltage secondary rail can no longer be achieved, thus at the end of the SWITCHING PHASE, no PWM condition can be encountered. The LW latch is reset. At the next WORKING PHASE a NORMAL mode status takes place. In order to become independent of the recovery time constant on the secondary side of the SMPS an additional reset input R2 is provided on the MODE latch. The condition Idemag<24µA corresponds to the activation of the secondary reconfiguration status. The R2 reset insures a return into the NORMAL mode following the first START–UP PHASE. Pulsed Mode Duty Cycle Control

During the sleep mode of the SMPS the switch S3 is closed and the control input pin 3 is connected to a 4.6V voltage source thru a 500W resistor. The discharge rate of the VCC capacitor is given by ICC–latch (device consumption during the LATCHED OFF phase) in addition to the current drawn out of the pin 3. Connecting a resistor between the Pin 3 and GND (RDPULSED) a programmable current is drawn from the VCC through pin 3. The duration of the LATCHED OFF phase is impacted by the presence of the resistor RDPULSED. The equation 3 shows the relation to the pin 3 current. Pulsed Mode Phases

Equations 1 through 8 define and predict the effective behavior during the PULSED MODE operation. The equations 6, 7, and 8 contain K, Y, and D factors. These factors are combinations of measured parameters. They appear in the parameter section “Kfactors for pulsed mode operation” page 4. In equations 3 through 8 the pin 3 current is the current defined in the above section “Pulsed Mode Duty Cycle Control”.

MC44608 EQUATION 1 Start–up Phase Duration:

t start–up

+

C

* UVLO2)

(Vstup I stup

Vcc

where: Istup is the start–up current flowing through VCC pin CVcc is the VCC capacitor value EQUATION 2 Switching Phase Duration:

t

+ switch

C

*

(Vstup UVLO1) I I ccS G

Vcc

)

where: IccS is the no load circuit consumption in switching phase IG is the current consumed by the Power Switch EQUATION 3 Latched–off Phase Duration:

t

C Vcc + latched*off

(UVLO1 I

ccL

* UVLO2)

) Ipin3

where: IccL is the latched off phase consumption Ipin3 is the current drawn from pin3 adding a resistor EQUATION 4 Burst Mode Duty Cycle:

d

BM

+t

t

start*up ) t switch ) t latched*off switch

EQUATION 5 C d

+C BM

EQUATION 6 d

BM

+ 1

*

(V UVLO2) stup I stup

Vcc

)

ǒ

k

ń

S Stup

I

)

)

I ccS G I stup

C

Vcc

Vcc

Ǔǒ

*

(V UVLO1) stup I I ccS G (V UVLO1) stup I I ccS G

) * )

1

)

k

ń

S L

where: kS/Stup = (Vstup – UVLO2)/(Vstup – UVLO1) kS/L = (UVLO1 – UVLO2)/(Vstup – UVLO1)

)

Ǔ

) IG I )I ccL pin3 I

ccS

C

* ) I ccL pin3

(UVLO1 UVLO2)

Vcc I

MC44608

ǒ ǒ

EQUATION 7 d

BM

ȡȧ Ȣ

+ 1

)

I

ǓǓȣȧȤ

1

)

I ccS G I stup

k

) SńStup

k

ń

I

S L

stup I I ccL pin3

)

EQUATION 8 d

BM

+ 1

ȡȧ )ȥ ȧȢ

ȡȧ ȧȧ ń Ȣ

ǒ Ǔ )I G I

k1

k

stup

1

S Stup

) (kSńL

)

k2

ǒǓ

ȣȧȣȧ ȧȧȦȧ ȤȤ

1 ) I pin3 I stup

where: k1 = Iccs/Istup k2 = IccL/Istup kS/Stup = (Vstup–UVLO2)/(Vstup–UVLO1) kS/L = (UVLO1–UVLO2)/(Vstup–UVLO1)

PULSED MODE CURRENT SENSE CLAMPING LEVEL Equations 9, 10, 11 and 12 allow the calculation of the Rcs value for the desired maximum current peak value during the SMPS stand–by mode. EQUATION 9

Ipk

stby

+ Vcs–th *R(Rcs

I cs)

S

where: Vcs–th is the CS comparator threshold Ics is the CS internal current source RS is the sensing resistor Rcs is the resistor connected between pin 2 and RS EQUATION 10

Ipk

stby

+ Vcs–th

1

*

ǒ

Ǔ

Ics V cs–th

R cs R

S

EQUATION 11

Ipk

+ Vcs–th stby

1

* (Rcs

) Y cs–stby R

S

where: Ycs–stby = Ics/Vcs–th Taking into the circuit propagation delay (dtcs) and the Power Switch reaction time (dtps): EQUATION 12

Ipk

+ stby

ƪ

1 V cs–th

* (Rcs

Y ) cs–stby R

S

ƫ

) Vin

(dt cs Lp

) dtps)

MC44608 60

5.08 5.07

50

5.06 t_rise

5.05 Vpin3 (V)

Time (nS)

85° C

5.04

40 t_fall 30

5.03 25° C

5.02 5.01

–25° C

5.00

20

4.99 10 10

11

12

13

14

4.98 0.5

15

1

1.5

2

2.5

Current Injected in Pin 3 (mA)

Pin6 VCC Voltage (V)

Figure 8. Output Switching Speed

Figure 11. Vpin3 During the Working Period 5.0

79.0

4.5

85° C 77.0 75.0

25° C

Vpin3 Voltage (V)

Frequency

–25° C

4.0

–25° C

73.0 71.0 69.0

3.5 25° C 3.0 85° C 2.5 2.0

67.0 65.0 10

11

12

13

14

1.5 –1.6

15

–1.4

–1.2

VCC Voltage (V)

80

4.60

70

4.40

60

4.20

Pin6 Current (mA)

Switching Duty Cycle (%)

4.80

85° C –25° C

30 25° C

10 0.5

1.0

–.04

–.02

0.0

–25° C

4.00

25° C

3.80 3.60 85° C

3.40

20

0 0.0

–.06

Figure 12. Vpin3 During the Latched Off Period

90

40

–.08

Current Injected in Pin 3 (mA)

Figure 9. Frequency Stability

50

–1.0

3.20 1.5

2.0

Current Injected in Pin3 (mA)

Figure 10. Duty Cycle Control

2.5

3.00 10

11

12

13

14

15

Pin6 VCC Voltage (V)

Figure 13. Device Consumption when Switching

MC44608 Figure 14. High Voltage Current Source

Figure 15. Overload Burst Mode

11.00

12.00 –25° C 11.00 Switching Duty Cycle (%)

10.00

–Icc (mA)

9.00 8.00 25° C 7.00 85° C 6.00

–25° C

10.00 9.00

25° C

8.00 85° C 7.00 6.00

5.00

5.00 0

100

200

300

400

500

0

100

Vi Pin8 Voltage (Vi)

200

300

Vi Pin Voltage (V)

Figure 16. Hiccup Mode Waveforms

The data in Figure 15 corresponds to the waveform in Figure 16. The Figure 16 shows VCC, ICC, Isense (pin 2) and Vout (pin 5). Vout (pin 5) in fact shows the envelope of the output switching pulses. This mode corresponds to an overload condition.

400

500

MC44608 The Figure 18 represents a complete power supply using the secondary reconfiguration. The specification is as follows: Input source: 85Vac to 265Vac 3 Outputs 112V / 0.45A 16V / 1.5A 8V / 1A Output power 80W Stand–by mode @ Pout = 300mW, 1.3W R F6 47288900

FI

C20 2N2FY

WIDE C1 AINS 100 nF

C11 220 pF 500 V

RFI FILTER R16 4.7 k W 4 kV C3 1 nF

D1, D2, D3, D4 1N5404

C5 220 m F 400 V

C4 1 nF D6 MR856

R5

D5 1N4007

100 k W

3 4

+

7 6 5

VCC

1

1

D9 MR852

11

2 10

R4 R3 0.27

2

mF

D13 1N4148

D10 MR852

8

R17 2.2 k W 5W

3.9 k W

C14 1000 35 V

R19 18 k W

D14 MR856

C8 100 nF

DZ1 MCR22–6

C16 120 pF

C9 470 pF 630 V MTP6N60E

3 16 V/1.5 A

3 8 V/1 A

7

Post Reg.

C15 + 1000 m F 16 V

mP

9

W

R21 47

W

R9 100 k W

OPT1

R11 4.7 k W

R12 1 kW

DZ3 10 V

C19 33 nF

Figure 17. Typical Application

C18 100 nF

R10 10 k W ON

DZ2 TL431CLP

J3

1

1N4934

+

R2 10 W

2

D12

C6 47 nF 630 V

C7 22 m F 16 V

C13 100 nF

C17 120 pF

R7 47 k W

D7 1N4148

8

MC44608P75

2

12

R1 22 k W 5W

6 1

112 V/0.45 A

C12 + 47 m F 250 V

+

Isense

D18 MR856

14

R8 2.4 k W

OFF ON = Normal Mode OFF = Pulsed Mode

J4

MC44608 The secondary reconfiguration is activated by the µP through the switch. The dV/dt appearing on the high voltage winding (pins 14 of the transformer) at every TMOS switch off, produces a current spike through the series RC network R7, C17. According to the switch position this spike is either absorbed by the ground (switch closed) or flows into the thyristor gate (switch open) thus firing the MCR22–6. The closed position of the switch corresponds to the Pulsed Mode activation. In this secondary side SMPS status the high voltage winding (12–14) is connected through D12 and DZ1 to the 8V low voltage secondary rail. The voltages

applied to the secondary windings 12–14, 10–11 and 6–7 (Vaux) are thus divided by ratio N12–14 / N9–8 (number of turns of the winding 12–14 over number of turns of the winding 9–8). In this reconfigured status all the secondary voltages are lowered except the 8V one. The regulation during every pulsed or burst is performed by the zener diode DZ3 which value has to be choosen higher than the normal mode regulation level. This working mode creates a voltage ripple on the 8V rail which generally must be post regulated for the microProcessor supply.

Figure 18. SMPS Pulsed Mode

The Figure 18 shows the SMPS behavior while working in the reconfigured mode. The top curve represents the VCC voltage (pin 6 of the MC44608). The middle curve represents the 8V rail. The regulation is taking place at 11.68V. On the bottom curve the pin 2 voltage is shown. This voltage represents the current sense signal. The pin 2 voltage

is the result of the 200µA current source activated during the start–up phase and also during the working phase which flows through the R4 resistor. The used high resolution mode of the oscilloscope does not allow to show the effective ton current flowing in the sensing resistor R11.

MC44608 PACKAGE DIMENSIONS DIP–8 P SUFFIX PLASTIC PACKAGE CASE 626–05 ISSUE K

8

NOTES: 1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS). 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.

5

–B– 1

4

F –A–

NOTE 2

L

C J

–T– N

SEATING PLANE

D H

M

K

G 0.13 (0.005)

M

T A

M

B

M

DIM A B C D F G H J K L M N

MILLIMETERS MIN MAX 9.40 10.16 6.10 6.60 3.94 4.45 0.38 0.51 1.02 1.78 2.54 BSC 0.76 1.27 0.20 0.30 2.92 3.43 7.62 BSC ––– 10_ 0.76 1.01

STYLE 1: PIN 1. 2. 3. 4. 5. 6. 7. 8.

AC IN DC + IN DC – IN AC IN GROUND OUTPUT AUXILIARY VCC

INCHES MIN MAX 0.370 0.400 0.240 0.260 0.155 0.175 0.015 0.020 0.040 0.070 0.100 BSC 0.030 0.050 0.008 0.012 0.115 0.135 0.300 BSC ––– 10_ 0.030 0.040

MC44608

ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, s, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.

PUBLICATION ORDERING INFORMATION NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada Email: [email protected] EUROPEAN TOLL–FREE ACCESS*: 00–800–4422–3781 *Available from , , Italy, England, Ireland

CENTRAL/SOUTH AMERICA: Spanish Phone: 303–308–7143 (Mon–Fri 8:00am to 5:00pm MST) Email: ONlit–[email protected] ON Semiconductor Website: http://onsemi.com

For additional information, please your local Sales Representative.